LanSafe for Windows ReadMe Version 5.0.3 Company Information ------------------- Powerware Headquarters 8609 Six Forks Road Raleigh, NC 27615 http://www.powerware.com Table of Contents ----------------- 1.0 Product Description 2.0 System Requirements 3.0 Before You Install - General 3.1 Unix Notes 4.0 Windows Installation 4.1 Windows Standard Install 4.1.1 Windows USB Installation 4.1.2 Windows Silent Installation 5.0 AIX Installation 5.1 Before You Install 5.2 AIX Install 6.0 HP-UX Installation 6.1 Before You Install 6.2 HP-UX Install 7.0 IRIX Installation 7.1 Before You Install 7.2 IRIX Install 8.0 Linux Installation 8.1 Before You Install 8.2 Linux Install 9.0 Mac OS X Installation 9.1 Before You Install 9.2 Mac OS X Install 10.0 NetWare Installation 10.1 Before You Install 10.2 NetWare Install 10.3 Stop the Power Monitor 10.4 Uninstall LanSafe 10.5 Reinstall LanSafe 11.0 SCO Installation 11.1 Before You Install 11.2 SCO Install 12.0 Solaris (Intel) Installation 12.1 Before You Install 12.2 Solaris (Intel) Install 13.0 Solaris (SPARC) Installation 13.1 Before You Install 13.2 Solaris (SPARC) Install 14.0 Additional Unix Instructions 14.1 Start LanSafe on a Unix system 14.3 Stop the Power Monitor 14.4 Uninstall LanSafe 15.0 Getting Started -------------------------------------------------------------------------------- 1.0 Product Description -------------------------------------------------------------------------------- LanSafe is power protection software that provides UPS monitoring, control, and preventive measures against power problems that affect computer networks and equipment. Together with Powerware UPS products, computer network systems protected by LanSafe software are more reliable and less prone to down time and data corruption. LanSafe is capable of connecting to UPSs that are directly connected to the network, in addition to those that are attached to computers via USB or serial ports. LanSafe can manage up to 64 computers that receive protected power from one UPS. -------------------------------------------------------------------------------- 2.0 System Requirements -------------------------------------------------------------------------------- Supported Platforms - Windows - HP-UX - IBM AIX - Linux - Mac OS - Novell NetWare - SCO OpenServer - SGI IRIX - Sun Solaris Windows Minimum Requirements - Installed TCP/IP networking - 200 MHz processor - 20 MB of RAM - 30 MB of available hard-disk space - Monitor resolution must be at least 800 by 600 pixels (1024 by 768 recommended) with 16 bit color (thousand of colors) Approximate Minimum Requirements for Other Operating Systems - Installed TCP/IP networking - 100 MHz processor - 32 MB of RAM - 16 MB of available hard-disk space !!!!!!!!!!!!!!! Read the release notes for exact operating system versions and system requirements. !!!!!!!!!!!!!!! -------------------------------------------------------------------------------- 3.0 Before You Install - General -------------------------------------------------------------------------------- - Install the latest service packs / operating system patches on your computer before installing LanSafe. - Uninstall all versions of LanSafe, including LanSafe III, before installing this product. - Turn on your UPS and let it warm-up for 30 seconds before attaching it to your computer. - Install the Powerware USB / Plug and Play driver if necessary. ------------------------------ 3.1 Unix Notes ------------------------------ The LanSafe Power Monitor automatically starts when the host computer is restarted in order to provide immediate protection. The autostart function is configured in one of the following ways. 1. If /etc/init.d or /sbin/init.d or /etc/rc.d/init.d exist, the ls.init file is placed in one of these directories. This file can be found in the install tar file inside /1_install/ directory. 2. If /etc/init.d, /sbin/init.d, or /etc/rc.d/init.d does not exist, and the file /etc/inittab exists, "PM:2345:once:$instpath/Bin/PowerMonitor.sh&" is added to the end of /etc/inittab file. Replace $instpath with the actual path for LanSafe directory. 3. If 1 and 2 failed, and if the file /etc/rc.d/rc.local exists, "$instpath/Bin/PowerMonitor&" is added to the end of the file /etc/rc.d/local. Replace $instpath with the actual path for LanSafe directory. -------------------------------------------------------------------------------- 4.0 Windows Installation -------------------------------------------------------------------------------- ------------------------------ 4.1 Windows Standard Install ------------------------------ When installing LanSafe for Windows you have three options: Option 1. Install LanSafe for a single computer connected to a single UPS. 1) Connect a UPS to the local workstation or to the network. Consult the UPS manual for more information. 2) The computer on which LanSafe will be installed should receive power from the UPS. 3) Run the LanSafe Installer. 4) Follow the instructions in the LanSafe Setup program for a "LanSafe Controller" installation. Option 2. Install LanSafe for multiple computers that receive power from a single UPS. 1) Choose one computer (Controller) to monitor and control the UPS and connect the UPS to this computer or to the network. Consult the UPS manual for more information. 2) Run the LanSafe Installer. 3) Follow the instructions in the LanSafe Setup program for a "LanSafe Controller" installation. 4) For each additional computer (Member) receiving power from the UPS, run the LanSafe Setup program on those computers and follow the instructions for a "LanSafe Member" installation. Option 3. Install only the main window (GUI) for remotely viewing UPS system status and accessing UPS management capabilities. 1) A LanSafe Only installation can be placed on any network connected computer. 2) Run the LanSafe Installer. 3) Follow the instructions in the LanSafe Setup program for a "LanSafe Only" installation. 4) A LanSafe icon is placed in the Windows Start menu. ------------------------------ 4.1.1 Windows USB Installation ------------------------------ For UPSs that communicate with a computer via Windows USB/Plug-and-Play, use the new standalone Powerware USB/Plug-and-Play driver. Follow the instructions in the driver ReadMe file (UPSDriversReadMe.txt) for information about installing this driver or upgrading your current driver. After the driver is installed, run the LanSafe installer as described in section 4.1. ------------------------------ 4.1.2 Windows Silent Installation ------------------------------ The LanSafe for Windows installer supports a silent installation mode. Silent installation is generally used for larger deployments of LanSafe over a network. For more information about silent installs consult the manual/online help. -------------------------------------------------------------------------------- 5.0 AIX Installation -------------------------------------------------------------------------------- ------------------------------ 5.1 Before You Install ------------------------------ - Uninstall all versions of LanSafe on the computer on which you will install this software. - The LanSafe SNMP agent will work only if the snmpd daemon was installed with the AIX operating system. Normally, that daemon is installed by default. ------------------------------ 5.2 AIX Install ------------------------------ 1) Access the LanSafe installer from a CD (1a) or a tar file (1b) 1a) Mount the CD-ROM For AIX 4: a. TYPE cd / b. TYPE mount –r –vcdrfs /dev/[cd1] /cdrom - Replace "[cd1]" with the device for your CD reader (e.g. cd0 or cd1). - The /cdrom can be replaced with any valid directory at root. Unmount the CD immediately after completing the installation procedure using the following procedure. a. TYPE cd / b. TYPE umount /cdrom For AIX 5: a. TYPE cd / b. TYPE mount –vcdrfs -oro /dev/[cd1] /mnt - Replace "[cd1]" with the device for your CD reader (e.g. cd0 or cd1). - The /mnt can be replaced with any valid directory at root. Unmount the CD immediately after completing the installation procedure using the following procedure. a. TYPE cd / b. TYPE umount /mnt Note: Mount commands for the various operating system versions may vary. Consult the MAN pages of your operating system for more information. 1b) Acquire the tar file a. Download tar file for AIX from the Powerware web site. or b. Copy the tar file from the Powerware Software CD. 2) Install LanSafe from a CD (2a) or a tar file (2b) 2a) Install LanSafe from a CD a. Mount the CD as specified in 1a above b. Navigate to the CD directory that contains the installer. TYPE cd /cdrom/Software/LanSafe/LanSafe5/Unix_Linux c. TYPE ./install.sh - If the above command fails, TYPE sh install.sh - The installer welcome text is displayed. d. Follow the installation prompts to install and configure LanSafe and the LanSafe SNMP agent. - Be sure to write down the access code you type during the configuration process. 2b) Install LanSafe from a tar file Note: This step assumes the tar file name is aix.tar. a. Extract installation script from tar file: TYPE tar xvf aix.tar install.sh b. TYPE ./install.sh aix.tar - The installer welcome text is displayed. c. Follow the installation prompts to install and configure LanSafe and the LanSafe SNMP agent. - Be sure to write down the access code you type during the configuration process. -------------------------------------------------------------------------------- 6.0 HP-UX Installation -------------------------------------------------------------------------------- ------------------------------ 6.1 Before You Install ------------------------------ - Uninstall all versions of LanSafe on the computer on which you will install this software. - To use the LanSafe SNMP agent, you must install the SNMP Extensible agent for the operating system. The SNMP Extensible agent is available for purchase from HP. - Before installing LanSafe on an HP-UX 10.20 system you must ensure all run time libraries are properly installed. In some regions the aCC run time libraries are not included as part of the standard installation of HP-UX 10.20. This should not be a problem in later versions of HP-UX since the aCC runtime libraries are included as part of the standard installation. The library patch is available from Hewlett-Packard Patch Name: PHSS_22354 Patch Description: s700_800 10.X HP aC++ runtime libraries (aCC A.01.21) Patch Dependencies: Check with HP to determine additional patch dependencies. ------------------------------ 6.2 HP-UX Install ------------------------------ 1) Access the LanSafe installer from a CD (1a) or a tar file (1b) 1a) Mount the CD-ROM For HP-UX 10.20: a. TYPE cd / b. TYPE mount /dev/dsk/[c0t0d0] /CDROM - Replace "[c0t0d0]" with the device for your CD reader. For HP-UX 11.0 and newer: a. TYPE cd / b. TYPE mount /dev/dsk/c0t0d0 /cdrom - Replace "[c0t0d0]" with the device for your CD reader. Unmount the CD immediately after completing the installation procedure using the following procedure. a. TYPE cd / b. TYPE umount /cdrom - Use /CDROM for 10.20 Note: Mount commands for the various operating system versions may vary. Consult the MAN pages of your operating system for more information. 1b) Acquire the tar file a. Download tar file for HP-UX from the Powerware web site. or b. Copy the tar file from the Powerware Software CD. 2) Install LanSafe from a CD (2a) or a tar file (2b) 2a) Install LanSafe from a CD a. Mount the CD as specified in 1a above b. Navigate to the CD directory that contains the installer. TYPE cd /cdrom/Software/LanSafe/LanSafe5/Unix_Linux c. TYPE ./install.sh - If the above command fails, TYPE sh install.sh - The installer welcome text is displayed. d. Follow the installation prompts to install and configure LanSafe and the LanSafe SNMP agent (if applicable). - Be sure to write down the access code you type during the configuration process. 2b) Install LanSafe from a tar file Note: This step assumes the tar file name is hpux.tar. a. Extract installation script from tar file: TYPE tar -xvf hpux.tar install.sh b. TYPE ./install.sh hpux.tar - The installer welcome text is displayed. c. Follow the installation prompts to install and configure LanSafe and the LanSafe SNMP agent (if applicable). - Be sure to write down the access code you type during the configuration process. -------------------------------------------------------------------------------- 7.0 IRIX Installation -------------------------------------------------------------------------------- ------------------------------ 7.1 Before You Install ------------------------------ - Uninstall all versions of LanSafe on the computer on which you will install this software. ------------------------------ 7.2 IRIX Install ------------------------------ 1) Access the LanSafe installer from a CD (1a) or a tar file (1b) 1a) Mount the CD-ROM a. TYPE cd / b. TYPE mount –t iso9660 /dev/rdsk/dks0d4vol /CDROM Unmount the CD immediately after completing the installation procedure using the following procedure. a. TYPE cd / b. TYPE umount /CDROM Note: Mount commands for the various operating system versions may vary. Consult the MAN pages of your operating system for more information. 1b) Acquire the tar file a. Download tar file for IRIX from the Powerware web site. or b. Copy the tar file from the Powerware Software CD. 2) Install LanSafe from a CD (2a) or a tar file (2b) 2a) Install LanSafe from a CD a. Mount the CD as specified in 1a above b. Navigate to the CD directory that contains the installer. TYPE cd /CDROM/Software/LanSafe/LanSafe5/Unix_Linux c. TYPE ./install.sh - If the above command fails, TYPE sh ./install.sh - The installer welcome text is displayed. d. Follow the installation prompts to install and configure LanSafe. - Be sure to write down the access code you type during the configuration process. 2b) Install LanSafe from a tar file Note: This step assumes the tar file name is irix.tar. a. Extract installation script from tar file: TYPE tar xvf irix.tar install.sh b. TYPE ./install.sh irix.tar - The installer welcome text is displayed. c. Follow the installation prompts to install and configure LanSafe. - Be sure to write down the access code you type during the configuration process. -------------------------------------------------------------------------------- 8.0 Linux Installation -------------------------------------------------------------------------------- ------------------------------ 8.1 Before You Install ------------------------------ - Uninstall all versions of LanSafe on the computer on which you will install this software. ------------------------------ 8.2 Linux Install ------------------------------ 1) Access the LanSafe installer from a CD (1a) or a tar file (1b) 1a) Mount the CD-ROM For RedHat: a. TYPE cd / b. TYPE mount /mnt/cdrom Unmount the CD immediately after completing the installation procedure using the following procedure. a. TYPE cd / b. TYPE umount /mnt/cdrom For SuSe: a. TYPE cd / b. TYPE mount /cdrom Unmount the CD immediately after completing the installation procedure using the following procedure. a. TYPE cd / b. TYPE umount /cdrom Note: Mount commands for the various operating system versions may vary. Consult the MAN pages of your operating system for more information. 1b) Acquire the tar file a. Download tar file for Linux from the Powerware web site. or b. Copy the tar file from the Powerware Software CD. 2) Install LanSafe from a CD (2a) or a tar file (2b) 2a) Install LanSafe from a CD a. Mount the CD as specified in 1a above b. Navigate to the CD directory that contains the installer. On RedHat: TYPE cd /mnt/cdrom/Software/LanSafe/LanSafe5/Unix_Linux On SuSe: TYPE cd /cdrom/Software/LanSafe/LanSafe5/Unix_Linux c. TYPE ./install.sh - If the above command fails, TYPE sh install.sh - The installer welcome text is displayed. d. Follow the installation prompts to install and configure LanSafe. - Be sure to write down the access code you type during the configuration process. 2b) Install LanSafe from a tar file Note: This step assumes the tar file name is linux.tar. a. Extract installation script from tar file: TYPE tar xvf linux.tar install.sh b. TYPE ./install.sh linux.tar - The installer welcome text is displayed. c. Follow the installation prompts to install and configure LanSafe. - Be sure to write down the access code you type during the configuration process. -------------------------------------------------------------------------------- 9.0 Mac OS X Installation -------------------------------------------------------------------------------- ------------------------------ 9.1 Before You Install ------------------------------ - Uninstall all versions of LanSafe on the computer on which you will install this software. - You must start the Macintosh Terminal application in order to type commands. The Terminal application is typically located on you computer in the following location MacintoshHD:Applications:Utilities:Terminal. ------------------------------ 9.2 Mac OS X Install ------------------------------ 1) Access the LanSafe installer from a CD (1a) or a tar file (1b) 1a) Mount the CD-ROM a. Insert the CD into the CD drive and close the drive. The CD will automatically mount in /Volumes 1b) Acquire the tar file a. Download tar file for Mac OS X from the Powerware web site. or b. Copy the tar file from the Powerware Software CD. 2) Install LanSafe from a CD (2a) or a tar file (2b) 2a) Install LanSafe from a CD a. Mount the CD as specified in 1a above b. Navigate to the CD directory that contains the installer. TYPE cd /Volumes/PW_Suite/Software/LanSafe/LanSafe5/Unix_Linux c. TYPE ./install.sh - If the above command fails, TYPE sh install.sh - The installer welcome text is displayed. d. Follow the installation prompts to install and configure LanSafe. - Be sure to write down the access code you type during the configuration process. 2b) Install LanSafe from a tar file Note: This step assumes the tar file name is macosx.tar. a. Extract installation script from tar file: TYPE tar -xvf macosx.tar install.sh b. TYPE ./install.sh macosx.tar - The installer welcome text is displayed. c. Follow the installation prompts to install and configure LanSafe - Be sure to write down the access code you type during the configuration process. -------------------------------------------------------------------------------- 10.0 NetWare Installation -------------------------------------------------------------------------------- ------------------------------ 10.1 Before You Install ------------------------------ - Uninstall all versions of LanSafe on the computer on which you will install this software. - Install the latest Support Pack for your operating system version. - You must have network file access to the SYS volume of the target NetWare server. ------------------------------ 10.2 NetWare Install ------------------------------ Note: The LanSafe installer for NetWare will write information in the AUTOEXEC.NCF file in SYS:\SYSTEM that instructs the operating system to automatically start LanSafe. All commands following the word "TYPE" in the procedures below should be entered at the system console command prompt. 1a) Mount the CD-ROM a. TYPE LOAD CDROM b. Put CD-ROM into NetWare CD-ROM drive c. TYPE VOLUME LIST - This verifies the CD is mounted d. Continue to step 2a or 2b 2a) Install LanSafe from a CD a. Mount the CD-ROM b. TYPE PW_SUITE_v5:\Software\LanSafe\LanSafe5\NetWare\pmsetup c. Replace PW_SUITE_v5 with your CD volume name if you are not using the Powerware software CD d. Follow the installation prompts to install and configure LanSafe. - Be sure to write down the access code you type during the configuration process. e. LanSafe will be automatically started after the file copy process. 2b) Install LanSafe from a temporary directory a. Create a directory named "temp" on the system volume. All directories in the path must have names that are 8 characters or less. b. Copy the LanSafe files to the temp directory. c. TYPE sys:temp\pmsetup d. Follow the installation prompts to install and configure LanSafe. - Be sure to write down the access code you type during the configuration process. e. LanSafe will be automatically started after the file copy process. f. Delete the files from the temporary directory. 3) Starting LanSafe on a NetWare system a. TYPE sys:\LanSafe\Bin\lansafe 4) Monitor and manage the Controller If the Power Monitor that you install is a Controller, you can view the status of the Controller from a Windows LanSafe installation. If you installed a Member, you must monitor the Controller to which the Member is linked. To monitor the Controller: a. Start LanSafe on a Windows-based computer. b. Use Open Controller to manage the Power Monitor. ------------------------------ 10.3 Stop the Power Monitor ------------------------------ You can stop the Power Monitor when needed. When the Power Monitor is stopped, the computer on which the software is installed is not protected by LanSafe. a. TYPE sys:\LanSafe\Bin\lsunload All Power Monitor processes are stopped. ------------------------------ 10.4 Uninstall LanSafe ------------------------------ The LanSafe uninstaller automatically stops LanSafe processes and removes files. a. TYPE sys:\LanSafe\Bin\pmremove Note: All LanSafe files and directories will be removed. ------------------------------ 10.5 Reinstall LanSafe ------------------------------ LanSafe Setup provides multiple software maintenance options when the LanSafe installer is run on a computer on which LanSafe is installed. a. Run the installer as specified above in NetWare Install. b. Select one of the reinstall options. "Reinstall LanSafe and all settings" – Reinstall all LanSafe components using the install wizard. All existing files will be removed. "Reinstall LanSafe application only" – Reinstalls the LanSafe application NLMs. User created files within the LanSafe directory are not removed. c. Follow the installation prompts to install and configure LanSafe. -------------------------------------------------------------------------------- 11.0 SCO Installation -------------------------------------------------------------------------------- ------------------------------ 11.1 Before You Install ------------------------------ - The LanSafe SNMP agent will work only if the snmpd daemon was installed with the SCO operating system. Normally, that daemon is installed by default. ------------------------------ 11.2 SCO Install ------------------------------ Note: The LanSafe installer for SCO writes information in the inittab file that instructs the operating system to automatically start LanSafe. 1) Access the LanSafe installer from a CD (1a) or a tar file (1b) 1a) Mount the CD-ROM For SCO 5: a. TYPE cd / b. TYPE mount -r –f HS /dev/[cd1] /mnt - Replace "[cd1]" with the device for your CD reader (e.g. cd0 or cd1). - The /mnt can be replaced with any valid directory at root. Unmount the CD immediately after completing the installation procedure using the following procedure. a. TYPE cd / b. TYPE umount /mnt Note: Mount commands for the various operating system versions may vary. Consult the MAN pages of your operating system for more information. 1b) Acquire the tar file a. Download tar file for SCO from the Powerware web site. or b. Copy the tar file from the Powerware Software CD. 2) Install LanSafe from a CD (2a) or a tar file (2b) 2a) Install LanSafe from a CD a. Mount the CD as specified in 1a above b. Navigate to the CD directory that contains the installer. TYPE cd /mnt/Software/LanSafe/LanSafe5/Unix_Linux c. TYPE ./install.sh - If the above command fails, TYPE sh install.sh - The installer welcome text is displayed. d. Follow the installation prompts to install and configure LanSafe and the LanSafe SNMP agent. - Be sure to write down the access code you type during the configuration process. 2b) Install LanSafe from a tar file Note: This step assumes the tar file name is sco.tar. a. Extract installation script from tar file: TYPE tar xvf sco.tar install.sh b. TYPE ./install.sh sco.tar - The installer welcome text is displayed. c. Follow the installation prompts to install and configure LanSafe and the LanSafe SNMP agent. - Be sure to write down the access code you type during the configuration process. -------------------------------------------------------------------------------- 12.0 Solaris (Intel) Installation -------------------------------------------------------------------------------- ------------------------------ 12.1 Before You Install ------------------------------ - Uninstall all versions of LanSafe on the computer on which you will install this software. ------------------------------ 12.2 Solaris (Intel) Install ------------------------------ 1) Access the LanSafe installer from a CD (1a) or a tar file (1b) 1a) Mount the CD-ROM a. TYPE cd / b. TYPE mount -F hsfs /dev/dsk/[c0t6d0s0] /cdrom - Replace "[c0t6d0s0]" with the device for your CD reader. Unmount the CD immediately after completing the installation procedure using the following procedure. a. TYPE cd / b. TYPE umount /cdrom Note: Mount commands for the various operating system versions may vary. Consult the MAN pages of your operating system for more information. 1b) Acquire the tar file a. Download tar file for Solaris from the Powerware web site. or b. Copy the tar file from the Powerware Software CD. 2) Install LanSafe from a CD (2a) or a tar file (2b) 2a) Install LanSafe from a CD a. Mount the CD as specified in 1a above b. Navigate to the CD directory that contains the installer. TYPE cd /cdrom/Software/LanSafe/LanSafe5/Unix_Linux c. TYPE ./install.sh - If the above command fails, TYPE sh install.sh - The installer welcome text is displayed. d. Follow the installation prompts to install and configure LanSafe. - Be sure to write down the access code you type during the configuration process. 2b) Install LanSafe from a tar file Note: This step assumes the tar file name is solint.tar. a. Extract installation script from tar file: TYPE tar -xvf solaris.tar install.sh b. TYPE ./install.sh solaris.tar - The installer welcome text is displayed. c. Follow the installation prompts to install and configure LanSafe. - Be sure to write down the access code you type during the configuration process. -------------------------------------------------------------------------------- 13.0 Solaris (SPARC) Installation -------------------------------------------------------------------------------- ------------------------------ 13.1 Before You Install ------------------------------ - Uninstall all versions of LanSafe on the computer on which you will install this software. ------------------------------ 13.2 Solaris (SPARC) Install ------------------------------ 1) Access the LanSafe installer from a CD (1a) or a tar file (1b) 1a) Mount the CD-ROM a. Insert the CD into the CD drive and close the drive. The CD will automatically mount in /cdrom Unmount the CD immediately after completing the installation procedure using the following procedure. a. TYPE cd / b. TYPE eject Note: Mount commands for the various operating system versions may vary. Consult the MAN pages of your operating system for more information. 1b) Acquire the tar file a. Download tar file for Solaris from the Powerware web site. or b. Copy the tar file from the Powerware Software CD. 2) Install LanSafe from a CD (2a) or a tar file (2b) 2a) Install LanSafe from a CD a. Mount the CD as specified in 1a above b. Navigate to the CD directory that contains the installer. TYPE cd /cdrom/Software/LanSafe/LanSafe5/Unix_Linux c. TYPE ./install.sh - If the above command fails, TYPE sh install.sh - The installer welcome text is displayed. d. Follow the installation prompts to install and configure LanSafe and the LanSafe SNMP agent (if applicable). - Be sure to write down the access code you type during the configuration process. 2b) Install LanSafe from a tar file Note: This step assumes the tar file name is solaris.tar. a. Extract installation script from tar file: TYPE tar -xvf solaris.tar install.sh b. TYPE ./install.sh solaris.tar - The installer welcome text is displayed. c. Follow the installation prompts to install and configure LanSafe and the LanSafe SNMP agent (if applicable). - Be sure to write down the access code you type during the configuration process. -------------------------------------------------------------------------------- 14.0 Additional Unix Instructions -------------------------------------------------------------------------------- This section provides details about how to start, stop, and uninstall LanSafe on Unix systems (AIX, HP-UX, IRIX, Mac OS, Linux, SCO, Solaris). ------------------------------ 14.1 Start LanSafe on a Unix system ------------------------------ If the LanSafe Power Monitor does not automatically start after a. Navigate to the Bin directory in the LanSafe install directory (the default install directory is /usr/Powerware/LanSafe/). TYPE cd /usr/Powerware/LanSafe/Bin b. TYPE ./PowerMonitor.sh 4) Start the SNMP agent on an AIX system a. Start AIX SNMP daemon if it is not started. TYPE snmpd b. Navigate to the Bin directory in the LanSafe install directory (the default install directory is /usr/Powerware/LanSafe/). TYPE cd /usr/Powerware/LanSafe/Bin c. TYPE ./PowerMonitorAgent & 5) Monitor and manage the Controller If the Power Monitor that you install is a Controller, you can view the status of the Controller from a Windows LanSafe installation. If you installed a Member, you must monitor the Controller to which the Member is linked. To monitor the Controller: a. Start LanSafe on a Windows-based computer. b. Use Open Controller to manage the Power Monitor. ------------------------------ 14.3 Stop the Power Monitor ------------------------------ You can stop the Power Monitor when needed. When the Power Monitor is stopped, the computer on which the software is installed is not protected by LanSafe. a. Navigate to the Bin directory in the LanSafe install directory (the default install directory is /usr/Powerware/LanSafe/). TYPE cd /usr/Powerware/LanSafe/Bin b. TYPE ./PowerMonitor.unload All Power Monitor processes are stopped. ------------------------------ 14.4 Uninstall LanSafe ------------------------------ The LanSafe uninstaller automatically stops LanSafe processes and removes files. a. Navigate to the Bin directory in the LanSafe install directory (the default install directory is /usr/Powerware/LanSafe/). TYPE cd /usr/Powerware/LanSafe/Bin b. TYPE ./uninstall.sh - If the above command fails, TYPE sh uninstall.sh Note: All files are removed, but the main LanSafe directory is not deleted. -------------------------------------------------------------------------------- 15.0 Getting Started -------------------------------------------------------------------------------- After completing the installation of LanSafe, view the online help on how to properly configure LanSafe.