AAL ATM Adaptation Layer
ABOR Abort
ACP Allied Communication Publication
AES Application Environment Specification
AH Authentication Header
ALE Automated Link Establishment
ALSP Aggregate Level Simulation Protocol
ANSI American National Standards Institute
API Application Programming Interface
ARIDPCM Adaptive Recursive Interpolated Differential Pulse Code
Modulation
ARP Address Resolution Protocol
ASD Assistant Secretary of Defense
ATA Army Technical Architecture
ATIS Alliance for Telecommunication Industry Solutions
ATM Asynchronous Transfer Mode
AUTODIN Automatic Digital Network
BER Bit Error Rate
BGP Border Gateway Protocol
BOOTP Bootstrap Protocol
bps Bits Per Second
BRI Basic Rate Interface
BUFR Binary Universal Format for Representation
C/S/A CINCs/Services/Agencies
C2 Command and Control
C2CDM Command and Control Core Data Model
C3I Command, Control, Communications, and Intelligence
C4I Command, Control, Communications, Computers, and
Intelligence
C4ISR Command, Control, Communications, Computers, Intelligence,
Surveillance, and Reconnaissance
CADRG Compressed Arc Digitized Raster Graphics
CAE Common Application Environment
CALS Continuous Acquisition and Life Cycle Support
CASE Computer Automated Software Engineering
CBS Commission for Basic Systems
CC Common Criteria for Information Technology Security
Evaluation
CCB Change Control Board
CCITT International Telegraph & Telephone Consultative Committee
(now ITU)
CDE Common Desktop Environment
CDENext Next Version of CDE
CDMA Code Division Multiple Access
CFS Center for Standards
CG Commanding General
CGI Computer Graphics Interface
CGM Computer Graphics Metafile
CIB Controlled Image Base
CIDE Communication Information Data Exchange
CINC Commander In Chief
CIO Central Imagery Office
CIPSO Common Internet Protocol Security Options
CJCSI Chairman of the Joint Chiefs of Staff Instruction
CJCSM Chairman of the Joint Chiefs of Staff Memo
CM Configuration Management
CMMS Conceptual Models of the Mission Space
CNR Combat Net Radio
COE Common Operating Environment
CONUS Continental United States
CORBA Common Object Request Broker Architecture
COSE Common Open Software Environment
COTS Commercial Off-the-Shelf
CRM Computer Resources Management
CSMA/CD Carrier Sense Multiple Access / Collision Detection
CTCPEC Canadian Trusted Computer Product Evaluation Criteria
DAA Designated Approving Authority
DAMA Demand Assigned Multiple Access
DBDB Digital Bathymetric Database
DBMS Database Management System
DCA Defense Communications Agency (now DISA)
DCAC Defense Communications Agency Circular (now DISA)
DCE Distributed Computing Environment
DDDS Defense Data Dictionary System
DDM DoD Data Model
DDRS Defense Data Repository System
DEF Data Exchange Format
DGSA DoD Goal Security Architecture
DHCP Dynamic Host Configuration Protocol
DIA Defense Intelligence Agency
DIGEST Digital Geographic Information Exchange Standard
DII Defense Information Infrastructure
DIS Distributed Interactive Simulation
DIS Draft International Standard
DISA Defense Information Systems Agency
DISN Defense Information Systems Network
DLWG Data Link Working Group
DMA Defense Mapping Agency
DMAL Defense Mapping Agency List
DMS Defense Message System
DMTD Digital Message Transfer Device
DNC Digital Nautical Chart
DNS Domain Name System
DoD Department of Defense
DoDD DoD Directive
DoDISS DoD Index of Specifications and Standards
DoDSSP DoD Single Stock Point
DPPDB Digital Point Positioning Data Base
DSIC Defense Standards Improvement Council
DSN Defense Switched Network
DSP Defense Standardization Program
DTED Digital Terrain Elevation Data
DTOP Digital Topographic Data
EEI External Environment Interface
EHF Extremely High Frequency
EIA Electronics Industries Association
E-MAIL Electronic Mail
ESP Encapsulating Security Payload
FAQ Frequently Asked Questions
FDDI Fiber Distributed Data Interface
FDMA Frequency Division Multiple Access
FED-STD Federal Telecommunication Standard
FIPS Federal Information Processing Standards
FPLMTS Future Public Land Mobile Telecommunications Systems
FTP File Transfer Protocol
GCCS Global Command and Control System
GCSS Global Combat Support System
GIF Graphics Interchange Format
GIS Geographic Information System
GKS Graphical Kernel System
GOTS Government Off-the-Shelf
GPS Global Positioning System
GRIB Gridded Binary
GSS Generic Security Service
GUI Graphical User Interface
HCI Human-Computer Interface
HF High Frequency
HITL Human-in-the-Loop
HLA High Level Architecture
HTML Hypertext Markup Language
HTTP Hypertext Transfer Protocol
I&RTS Integrated and Runtime Specification
IAB Internet Architecture Board
ICCCM Inter-Client Communications Convention Manual
ICMP Internet Control Message Protocol
IDEF Integrated (Computer-Aided Manufacturing) Definition
IDEF1X Integrated Definition for Information Modeling
IDEF0 Integrated Definition for Function Modeling
IDUP Independent Data Unit Protection
IEC International Electrotechnical Commission
IEEE Institute of Electrical and Electronic Engineers
IER Information Exchange Requirements
IESG Internet Engineering Steering Group
IETF Internet Engineering Task Force
IF Intermediate Frequency
IGMP Internet Group Management Protocol
IMETS Integrated Meteorological System
IP Internet Protocol
IPCP Internet Protocol Control Protocol
IPv4 IP Next Generation/Version 4
IPv6 IP Next Generation/Version 6
IS Information System
ISDN Integrated Services Digital Network
ISO International Organization for Standardization
ISP International Standardized Profile
ISP ISDN Security Program
ISS Intelligence Systems Secretariat
ITSEC European Information Technology Security Evaluation
Criteria
ITSG Information Technology Standards Guidance
ITU International Telecommunications Union (formerly called
CCITT)
ITU-T International Telecommunications Union - Telecommunications
Standardization Sector
JCSA Joint C4ISR System Architecture
JFIF JPEG File Interchange Format
JIEO Joint Interoperability & Engineering Organization
JPEG Joint Photographic Expert Group
JTA Joint Technical Architecture
JTA WG Joint Technical Architecture Working Group
JTDLMP Joint Tactical Data Link Management Plan
JTIDS Joint Tactical Information Distribution System
kbps Kilobits Per Second
kHz Kilohertz
KMP Key Management Protocol
LAN Local Area Network
LCP Link Control Protocol
LDR Low Data Rate
LOS Line-of-Sight
LWD Littoral Warfare Data
M&S Modeling and Simulation
MAGTF Marine Air Ground Task Force
MAN Metropolitan-Area Network
MAU Medium-Access Unit
Mbits/s Megabits per second
MC&G Mapping, Charting and Geodesy
MCCDC Marine Corps Combat Development Command
MDR Medium Data Rate
MHP Mobile Host Protocol
Mhz Megahertz
MIB Management Information Base
MIDB Management Information Database
MIDS Multi-functional Information Distribution System
MIL-HDBK Military Handbook
MILSATCOM Military Satellite Communications
MIL-STD Military Standard
MISSI Multilevel Information Systems Security Initiative
MOSPF Multicast Open Shortest Path First
MPEG Motion Pictures Expert Group
MSMP Modeling and Simulation Master Plan
MSP Message Security Protocol
NATO North Atlantic Treaty Organization
NCSC National Computer Security Center (see NSA)
NIST National Institute of Standards and Technology
NITFS National Imagery Transmission Format Standard
NSA National Security Agency
NTIS National Technical Information Service
NTP Network Time Protocol
ODBC Open Data Base Connectivity
ODMG Object Data Management Group
OLE Object Linking Embedding
OMA Object Management Architecture
OMG Object Management Group
OODBMS Object-Oriented Database Management System
OOM Object-Oriented Methods
OOT Object Oriented Technology
OSD Office of the Secretary of Defense
OSF Open Software Foundation
OSI Open Systems Interconnection
OSPF Open Shortest Path First
PCAT PC Access Tool
PCMCIA Personal Computer Memory Card International Association
PCS Personal Communications Services
PDU Protocol Data Units
PHIGS Programmers Hierarchical Interactive Graphics Systems
PM Program Manager
PN-NI Private Network-Network Interface
POC Point of Contact
POSIX Portable Operating System for Information Exchange
PPP Point-to-Point Protocol
PPS Precise Position Service
PRI Primary Rate Interface
PSK Phase Shift Keying
PSM Persistent Stored Modules
PST Prestructured Technology
PSTN Public Switched Telephone Networks
RDBMS Relational Database Management System
RF Radio Frequency
RFC Request for Comments
RFP Requests for Proposals
RPC Remote Procedure Call
RPF Raster Product Format
RTI Run Time Infrastructure
SAMP Security Association Management Protocol
SATCOM Satellite Communications
SCC Standards Coordinating Committee
SDN Secure Data Network
SDNS Secure Data Network System
SEDRIS Synthetic Environment and Data Representation Interchange
Specification
SGML Standard Generalized Markup Language
SHF Super High Frequency
SIDR Secure Intelligence Data Repository
SILS Standard for Interoperable LAN Security
SNMP Simple Network Management Protocol
SNMPv1 Structure of Management Information
SONET Synchronous Optical Network
SOW Statements of Work
SSL Secure Socket Layer
STANAG Standardization Agreement
STD Standard
STOU Store Unique
STS Synchronous Transport Signal
SUS Single UNIX Specification
TACO2 Tactical Communications Protocol 2
TADIL Tactical Digital Information Link
TAFIM Technical Architecture Framework for Information Management
TAWDS Tactical Automated Weather Distribution System
TCP Transmission Control Protocol
TCSEC Trusted Computer Security Evaluation Criteria
TDL Tactical Data Link
TDMA Time Division Multiple Access
TELNET Telecommunications Network
TFTP Trivial File Transfer Protocol
TIA Telecommunications Industry Association
TIDP Technical Interface Design Plan
TIS Technical Interface Specification
TOS Type-of-Service
TP0 Transport Protocol Class 0
TRC Technical Reference Code
TRM Technical Reference Model
TSIG Trusted Systems Interoperability Group
TSIX(RE) Trusted Security Information Exchange for Restricted
Environments
UCS Universal Multiple-Octet Coded Character Set
UDP User Datagram Protocol
UHF Ultra High Frequency
UI User Interface
UNI User-Network Interface
URL Uniform Resource Locator
USD(A&T) Under Secretary of Defense for Acquisition and Technology
USIS United States Imagery System
USMC U.S. Marine Corps
USMTF United States Message Text Format
UVMap Urban Vector Map
VHF Very High Frequency
VITD Vector Product Interim Terrain Data
VMap Vector Map
VMap AD VMap Aeronautical Data
VMF Variable Message Format
VPF Vector Product Format
VTC Video Teleconferencing
WGS World Geodetic System
WMO World Meteorological Organization
WNDP Worldwide Numbering and Dialing Plan
WVS+ World Vector Shoreline Plus
WWW World Wide Web
APPENDIX B LIST OF MANDATED STANDARDS AND SOURCES
This appendix summarizes the mandated standards from the Joint Technical Architecture (JTA), and provides references to locations where the standards may be obtained. The mandated standards from Sections 2 through 6 are summarized in a set of tables, with one table per section. The first column in each table contains a reference to the JTA section where the standards is mandated. When there are multiple standards mandated in a section, only the first standard contains a reference.
The second column contains the full citation for the mandated standard, including an identifying number, date, and title. Where the standards are available electronically, the tables contain an electronic link to the standard. These links are accessible in the on-line World Wide Web (WWW) version of the JTA.
If the mandated standard is based on other standards (e.g. it is a Government profile of one or more industry standards), the third column identifies the "base standards" that are referenced by the mandated standard. These are included a convenience to allow greater understanding of the scope of these mandated standards. Depending on how the base standards are referenced in the mandated standard, part or all of the base standards may implicitly also be mandated.
The second part of this appendix provides instructions for obtaining copies of the standards cited in the JTA. Where possible, this section also contains electronic links to the appropriate organization, accessible in the WWW version of the JTA.
JTA SECTION & MANDATED STANDARD, TITLE, & DATE BASE STANDARDS
SERVICE AREA PROFILED
2.2.2.1.2 FIPS Pub 158-1: 1993, User Interface
User Interface Component of the Application
Services Portability Profile, X-Windows Version
11, Release 5
- OSF Motif Application Environment
Specification (AES) Release 1.2, 1992
- OSF/Motif Motif Inter Client
Communications Convention Manual
(ICCCM)
- Win32 APIs, Window Management and
Graphics Device Interface, Volume 1
Microsoft Win32 Programmers Reference
Manual, 1993, Microsoft Press
- X/Open C323 Common Desktop Environment
(CDE) Version 1.0, April 1995
2.2.2.1.3 FIPS Pub 127-2: 1993, Database Language ISO 9075: 1992
Data Management for Relational DBMSs Database Language
Services for Relational
DBMSs
- Open Database Connectivity ODBC 2.0
2.2.2.1.4.1 ISO 8879: 1986, Standard Generalized
Document Markup Language (SGML)
Interchange
- RFC-1866: 1995, Hypertext Markup
Language (HTML), Internet Version 2.0
2.2.2.1.4.2 FIPS Pub 128-1: 1993, Computer Graphics ISO 8632.1-4:
Graphics Data Metafile (CGM) - Interchange format for 1992
Interchange vector graphics data Computer Graphics
Metafile (CGM) -
Interchange
format for vector
graphics data.
- JPEG File Interchange Format (JFIF), ISO/IEC 10918-1:
Version 1.02, C-Cube Microsystems for 1994
raster graphics data Joint Picture
Expert Group
(JPEG) algorithm
2.2.2.1.4.3 MIL-STD-2411, Raster Product Format
Geospatial Data (RPF)
Interchange
- MIL-STD-2407, Interface Standard for
Vector Product Format (VPF)
- MIL-STD-2401, World Geodetic System 84
(WGS-84), 21 March 1994
- DMAL 805-1A, DMA List of Products and
Services, March 1994
2.2.2.1.4.4 MIL-STD-2500A, National Imagery
Imagery Data Transmission Format (Version 2.0) for
Interchange file format
- MIL-STD-188-196, Bi-Level Image
Compression
- MIL-STD-188-199, Vector Quantization
Decompression
- MIL-STD-2301 ANSI/ISO
8632:1992
Computer Graphics
Metafile (CGM)
- ISO/IEC 10918-1: 1994, Joint
Photographic Experts Group (JPEG), as
profiled by MIL-STD-188-198A
2.2.2.1.4.6 ISO/IEC 11172-1:1993 - Encoding of
Sound Data moving pictures and associated audio
Interchange for digital storage media at up to
about 1.5 Mbits/s -- Part 1: Systems
- ISO/IEC 11172-3:1993 - Encoding of
moving pictures and associated audio
for digital storage media at up to
about 1.5 Mbits/s -- Part 3: Audio
- ISO/IEC 11172-3/Cor. 1:1995 - Encoding
of moving pictures and associated audio
for digital storage media at up to
about 1.5 Mbits/s -- Part 3: Audio
Technical Corrigendum
- ISO DIS 13818-1: 1996, Generic Coding
of Moving Pictures and Associated Audio
Information - Part 1: Systems
- ISO DIS 13818-3: 1995, Generic Coding
of Moving Pictures and Associated Audio
Information - Part 3: Audio
2.2.2.1.4.7 ISO/IEC 11172-1: 1993 Coding of moving
Video Data pictures and associated audio for
Interchange digital storage media at up to about
1.5 Mbits/s -- Part 1: Systems
- ISO/IEC 11172-1: 1993/Cor. 1:1995
Coding of moving pictures and
associated audio for digital storage
media at up to about 1.5 Mbits/s --
Part 1: Systems Technical Corrigendum 1
- ISO/IEC 11172-2: 1993 Coding of moving
pictures and associated audio for
digital storage media at up to about
1.5 Mbits/s -- Part 2 Video
- ISO DIS 13818-1: 1996, Generic Coding
of Moving Pictures and Associated Audio
Information - Part 1: Systems
- ISO DIS 13818-2: 1996 - Generic Coding
of Moving Pictures and Associated Audio
Information - Part 2: Video
2.2.2.1.4.8 FM 92-X-GRIB, The WMO Format for the
Atmospheric Storage of Weather Product Information
Data and the Exchange of Weather Product
Interchange Messages in Gridded Binary (GRIB) Form
- FM 94-X-BUFR, The WMO Binary Universal
Format for Representation (BUFR) of
meteorological data.
- Data Exchange Format (DEF), Appendix 30
to the TAWDS/IMETS Implementation
Document for Communication Information
Data Exchange (CIDE)
2.2.2.1.4.9 FM 94-X-BUFR, The WMO Binary Universal
Oceanographic Format for Representation (BUFR) of
Data oceanographic data.
Interchange
2.2.2.1.5 ISO 7942: 1985, as profiled by FIPS Pub
Graphic 120-1 (change notice 1): 1991,
Services Graphical Kernel System (GKS) - for 2-D
graphics
- ISO 9592: 1989, as profiled by FIPS Pub
153, Programmers Hierarchical
Interactive Graphics Systems (PHIGS) -
for 3-D graphics
- ISO/IEC 9636: 1991, Information
Technology-Computer
Graphics-Interfacing (CGI) Techniques
for Dialogue with Graphics Devices
2.2.2.1.7 ISO 9945-1: 1990, Information
Operating Technology - Portable Operating System
System Services Interface for Computer Environments
(POSIX) - Part 1: System Application
Program Interface (API) [C language],
(as profiled by FIPS PUB 151-2: 1993)
- ISO 9945-2: 1993, Information
Technology - Portable Operating System
Interface for Computer Environments
(POSIX) - Part 2: Shell and Utilities,
(as profiled by FIPS PUB 189: 1994)
- IEEE 1003.2d: 1994, POSIX - Part 2:
Shell and Utilities - Amendment: Batch
Environment
- IEEE 1003.1b: 1993, POSIX - Part 1:
System Application Program Interface
(API) Amendment 1; Real Time Extension
[C Language]*, (as profiled by FIPS Pub
151-2: 1993)
- IEEE 1003.1i: 1995, POSIX - Part 1:
System Application Program Interface
(API) Amendment: Technical Corrigenda
to Real-time Extension [C Language]*
- IEEE 1003.1c: 1995
POSIX - Part 1: System Application
Program Interface (API) Amendment 2:
Threads Extension [C Language]
- Win32 APIs, Window Management and
Graphics Device Interface, Volume 1
Microsoft Win32 Programmers Reference
Manual, 1993, Microsoft Press.
2.2.2.2.1 ISO/IEC 8859-1:1987, Information
Internationaliza Processing - 8-Bit Single-Byte Coded
tion Services Character Sets - Part 1: Latin Alphabet
No. 1
- ISO/IEC 10646-1:1993, Information
Technology - Universal Multiple-Octet
Coded Character Set (UCS) - Part 1:
Architecture and Basic Multilingual
Plane
2.2.2.2.4.1 OSF -DCE Remote Procedure Call (RPC),
Remote Version 1.1, 1994
Procedure
Computing
- OSF - DCE Time Services, Version 1.1,
1994
- OSF - DCE Directory Services, Version
1.1, 1994
2.2.2.2.4.2 OMG - The Common Object Request Broker:
Distributed Architecture and Specification
Object (CORBA), Version 2: July 1995, (also
Computing available as: X/Open Common
Application Environment (CAE)
Specification P431 - Common Object
Request Broker Architecture &
Specification, Version 2)
- OMG - CORBA services: Common Object
Services Specification, March 1996
(also available as: X/Open CAE
Specification P432 - Common Object
Services, Volume 1 and X/Open CAE
Specification P502 - Common Object
Services, Volume 2)
- OMG - CORBA facilities: Common Object
Facilities Architecture, November 1995
Information Transfer Mandated Standards
JTA SECTION & MANDATED STANDARD, TITLE, & DATE BASE STANDARDS
SERVICE AREA PROFILED
3.2.1.1 IAB-Standard-3/RFC-1122/RFC-1123, Host
Host Standards Requirements, October 1989
3.2.1.1.1.1 ACP 123 US Supplement No 1, Common ACP 123:194
Electronic Mail Messaging Strategy and Procedures, ISO/IEC
- November 1995 8613-1:1993
- - ISO/IEC 8859:1990
- - ISO/IEC
- - 10021-1:1990
- - ISO/IEC
- - 10021-2:1990
- - ISO/IEC
- - 10021-4:1990
- - ISO/IEC
- - 10021-5:1990
- - ISO/IEC
- - 10021-6:1990
- - ISO/IEC
- - 10021-7:1990
- - ISO/IEC ISP
- - 10610-1:1993
- - ISO/IEC ISP
- - 10611-1:1994
- - ISO/IEC ISP
- - 10611-3:1994
- - ISO/IEC ISP
- - 10611-4:1994
- - ISO/IEC ISP
- - 10611-5:1994
- - ISO/IEC ISP
- - 12062-1:1994
- - ISO/IEC ISP
- - 12062-2:1994
- - ITU X.400:1992
- ITU X.402:1992
ITU X.411:1992
ITU X.413:1992
ITU X.419:1992
ITU X.420:1992
AMH2n (D)
AMH9n (D)
(MIL-STD-2045-1850
0)
3.2.1.1.1.2.1 ITU-T X.500, The Directory -- Overview
X.500 Directory of Concepts, Models and Services - Data
Services Communication Networks Directory, 1993
3.2.1.1.1.2.2 IAB Standard 13/RFC-1034/RFC-1035,
Domain Name Domain Name System, November 1987
System (DNS)
3.2.1.1.1.3 IAB Standard 9/RFC-959, File Transfer
File Transfer Protocol, October 1985
3.2.1.1.1.4 IAB Standard 8/RFC-854/RFC-855, Telnet
Remote Terminal Protocol, May 1983
3.2.1.1.1.5 IAB Standard 15/RFC-1157, Simple
Network Network Management Protocol (SNMP), May
Management 1990
- IAB Standard 16/RFC-1155/RFC-1212,
Structure of Management Information ,
May 1990
- IAB Standard 17/RFC-1213, Management
Information Base, March 1991
3.2.1.1.1.6 RFC-1305, Network Time Protocol (V3),
Network Time April 9, 1992
3.2.1.1.1.7 RFC- 951, Bootstrap Protocol, September
Bootstrap 1, 1985
Protocol
(BOOTP)
- RFC-1533, DHCP Options and BOOTP Vendor
Extensions, October 8, 1993
- RFC-1542, Clarifications and Extensions
for the Bootstrap Protocol, October 27,
1993
3.2.1.1.1.8 RFC-1541, Dynamic Host Configuration
Dynamic Host Protocol, October 27, 1993
Configuration
Protocol (DHCP)
3.2.1.1.1.9.1 RFC-1945, Hypertext Transfer Protocol
Hypertext -- HTTP/1.0, May 17, 1996
Transfer
Protocol (HTTP)
3.2.1.1.1.9.2 RFC-1738, Uniform Resource Locators,
Uniform December 20, 1994
Resource
Locator (URL)
- RFC-1808, Relative Uniform Resource
Locators, June 14, 1995
3.2.1.1.1.10 MIL-STD-2045-47001, Connectionless Data
Connectionless Transfer Application Layer Standard,
Data Transfer July 27, 1995
3.2.1.1.2.1.1 IAB-Standard 7/RFC-793, Transmission
Transmission Control Protocol, September 1981
Control
Protocol (TCP)
3.2.1.1.2.1.2 IAB-Standard 6/RFC-768, User Datagram
User Datagram Protocol, August 1980
Protocol (UDP)
3.2.1.1.2.1.3 IAB-Standard
Internet 5/RFC-791/RFC-950/RFC-919/RFC922/
Protocol (IP) RFC-792/RFC-1112, Internet Protocol,
September 1981
3.2.1.1.2.2 IAB-Standard 35/RFC-1006, ISO Transport
OSI/Internet Service on top of the TCP, May 1987
Interworking
Protocol
3.2.1.2 VTC001, Industry Profile for Video
Video Teleconferencing, Revision 1, April 25,
Teleconferencing 1995
(VTC)
Standards
- ITU-T H.324, Terminal for Low Bit Rate
Multimedia Communications, March 19,
1996
3.2.1.3.1 TIA/EIA-465-A, Group 3 Facsimile
Analog Apparatus for Document Transmission,
Facsimile March 21, 1995
Standards
- TIA/EIA-466, Procedures for Document
Facsimile Transmission, May 1981
3.2.1.3.2 MIL-STD 188-161D, Interoperability and
Digital Performance Standards for Digital
Facsimile Facsimile Equipment, January 10, 1995
Standard
3.2.1.4 MIL-STD-2045-44500, National Imagery
Secondary Transmission Standard (NITFS) Tactical
Imagery Communications Protocol 2 (TACO2), June
Dissemination 18, 1993
Standards
3.2.2.1 RFC-1812, Requirements for IP Version 4
Router Routers, June 22, 1995
Standards
- IAB Standard 6/RFC-768, User Datagram
Protocol, August 1980
- IAB Standard 7/RFC-793, Transmission
Control Protocol, September 1981
- IAB Standard 8/RFC-854/RFC-855, TELNET
Protocol, May 1983
- IAB Standard 13/RFC-1034/RFC-1035,
Domain Name System, November 1987
- IAB Standard 15/RFC-1157, Simple
Network Management Protocol, May 1990
- IAB Standard 16/RFC-1155/RFC-1212,
Structure of Management Information,
May 1990
- IAB Standard 17/RFC-1213, Management
Information Base, March 1991
- RFC-951, Bootstrap Protocol, September
1, 1985
- RFC-1533, DHCP Options and BOOTP Vendor
Extensions, October 8, 1993
- RFC-1541, DHCP, October 27, 1993
- RFC-1542, Clarifications and Extensions
for the Bootstrap Protocol, October
27, 1993
- IAB Standard 33/RFC-1350, Trivial FTP
(TFTP), July 1992, to be used for
initialization only.
3.2.2.1.1 IAB Standard
Internet 5/RFC-791/RFC-950/RFC-919/RFC-922/
Protocol (IP) RFC-792/RFC-1112, Internet Protocol,
September 1981
3.2.2.1.2.1 RFC-1583, Open Shortest Path First
Interior Routing Version 2, for unicast routing,
Routers March 23, 1994
- RFC-1584, Multicast Extensions to OSPF,
March 24, 1994, for multicast routing
3.2.2.1.2.2 RFC-1771, Border Gateway Protocol 4,
Exterior March 21, 1995
Routers
- RFC-1772, Application of BGP In the
Internet, March 21, 1995
3.2.2.2.1 ISO/IEC 8802-3: 1993, Carrier Sense
Local Area Multiple Access with Collision
Network (LAN) Detection (CSMA/CD) Access Method and
Physical Layer Specifications, 10BaseT
MediumAccess Unit (MAU)
- IAB Standard 41/RFC-894, Standard for
the Transmission of IP Datagrams Over
Ethernet Networks, April 1984
- IAB Standard 37/RFC-826, An Ethernet
Address Resolution Protocol, November
1982
3.2.2.2.2 IAB Standard 51/RFC-1661/RFC-1662,
Point to Point Point-to-Point Protocol (PPP), July
Standards 1994
- RFC-1332, PPP Internet Protocol Control
Protocol (IPCP), May 26, 1992
- RFC-1333, PPP Link Quality Monitoring,
May 26, 1992
- RFC-1334, PPP Authentication Protocols,
October 20, 1992
- RFC-1570, PPP Link Control Protocol
(LCP) Extensions, January 11, 1994
- EIA 232E, Interface Between Data
Terminal Equipment and Data Circuit
Terminating Equipment Employing Serial
Binary Data Interchange, July 1991
- EIA 449, General Purpose 37-Position
and 9-Position Interface for Data
Terminal Equipment and Data Circuit
Terminating Equipment Employing Serial
Binary Data Interchange, February 1980
- EIA 530A, High Speed 25-Position
Interface for Data Terminal Equipment
and Data Circuit-Terminating Equipment,
June 1992, Including Alternate
26-Position Connector, 1992
3.2.2.2.3 MIL-STD-188-220A, Interoperability
Combat Net Standard for Digital Message Transfer
Radio (CNR) Device (DMTD) Subsystems, July 27, 1995
Networking
3.2.2.2.4 ANSI T1.601, Telecommunications -
Integrated Integrated Services Digital Network
Services Data (ISDN) - Basic Access Interface for Use
Network (ISDN) on Metallic loops for Application on
the Network Side of the NT (Layer 1
Specification), 1992
- ANSI T1.408, Telecommunications -
Integrated Services Digital Network
(ISDN) - Primary Rate - Customer
Installation Metallic Interfaces (Layer
1 Specification), 1990
- ITU-T Q.921, ISDN User-Network
Interface - Data Link Layer
Specification - Digital Subscriber
Signaling System No. 1, 1993
- ITU-T Q.931, ISDN User-Network
Interface Layer 3 Specification for
basic Call Control - Digital Subscriber
Signaling System No. 1(DSS 1), Network
Layer, User-Network Management, 1989
- ITU-T E.164, Numbering Plan for the
ISDN Era, 1991
- DCAC 370-175-13, Defense Switched
Network System Interface Criteria,
section titled Worldwide Numbering and
Dialing Plan (WNDP), September 1993
- RFC-1356, Multiprotocol Interconnect on
X.25 and ISDN in the Packet Mode,
August 6, 1992
- RFC-1618, PPP over ISDN, May 13, 1994
3.2.2.2.5 ATM Forum's UNI Specification V 3.1,
Asynchronous User-Network Interface, September 1994
Transfer Mode
(ATM)
- ANSI T1.630 ATM Adaptation Layer for
Constant Bit Rate Services
Functionality and Specifications, 1993
- ANSI T1.635 ATM Adaptation Layer Type 5
Common Part Functions and
Specifications, 1994, which adopts
ITU-T I.363, section 6
- RFC-1577, Classical IP and Address
Resolution Protocol (ARP) over ATM,
January 20, 1994
3.2.3.1.1.1 MIL-STD-188-181, Interoperability
5- and 25-kHz Standard for Dedicated 5-kHz and 25-kHz
Service UHF Satellite Communications,
September 18, 1992
3.2.3.1.1.2 MIL-STD-188-182, Interoperability
5-kHz DAMA Standard for 5 kHz UHF DAMA Terminal
Service Waveform, September 18, 1992
3.2.3.1.1.3 MIL-STD-188-183, Interoperability
25-kHz Standard for 25 kHz UHF/TDMA/DAMA
TDMA/DAMA Terminal Waveform, September 18, 1992
Service
3.2.3.1.1.4 MIL-STD-188-184, Interoperability and
Data Control Performance Standard for the Data
Waveform Control Waveform, August 20, 1993
3.2.3.1.2.1 MIL-STD-188-164, Interoperability and
Earth Terminals Performance Standards for C-Band,
X-Band, and Ku-Band SHF Satellite
Communications Earth Terminals, January
13, 1995
3.2.3.1.2.2 MIL-STD-188-165, SHF Interoperability
Phase Shift and Performance Standards for SHF
Keying (PSK) Satellite Communications PSK Modems
Modems (Frequency Division Multiple Access
(FDMA) Operations), January 13, 1995
3.2.3.1.3.1 MIL-STD-1582, EHF LDR Uplinks and
Low Data Rate Downlinks, December 10, 1992
(LDR)
3.2.3.1.3.2 MIL-STD-188-136, EHF MDR Uplinks and
Medium Data Downlinks, August 26, 1995
Rate (MDR)
3.2.3.2.1.1 MIL-STD-188-141A, Medium and High
Automated Link Frequency Radio Equipment Standard,
Establishment September 10, 1993
3.2.3.2.1.2 MIL-STD-188-148, Interoperability
Anti-Jamming Standard Anti-Jam Communications (2-30
Capability Mhz), April 13, 1992
3.2.3.2.1.3 MIL-STD-188-110A, Data Modems,
Data Modems Interoperability and Performance
Standards, September 30, 1991
3.2.3.2.1.4 MIL-STD-188-242, Tactical Single
Very High Channel (VHF) Radio Equipment, June 20,
Frequency (VHF) 1985
3.2.3.2.1.5 MIL-STD-188-243, Tactical Single
Ultra High Channel (UHF) Radio Communications,
Frequency (UHF) March 15, 1989
3.2.3.2.1.6 MIL-STD-188-145, Digital Line-of-Sight
Super High (LOS) Microwave Radio Equipment, July
Frequency (SHF) 28, 1992
3.2.3.2.5 JTDIS System Segment Specification
JTDIDS/MIDS (Class 2 Terminal)
Transmission
Media
STANAG 4175, Edition 1, August 29, 1991
- Technical Characteristics of the
Multifunctional Information
Distribution System (MIDS)
3.2.3.3 ANSI T1.105, Telecommunications -
SONET Synchronous Optical Network (SONET) -
Transmissions Basic Description Including Multiplex
Structure, Rates and Formats (ATIS)
(Revision and Consolidation of ANSI
T1.105-1991 and ANSI T1.105A-1991),
1995
- ANSI T1.107, Digital Hierarchy -
Formats Specifications, 1995
- ANSI T1.117, Digital Hierarchy -
Optical Interface Specifications
(SONET) (Single Mode - Short Reach),
1991
JTA SECTION & MANDATED STANDARD, TITLE, & DATE BASE STANDARDS
SERVICE AREA PROFILED
4.2.1 FIPS PUB 183, Integration Definition for
Activity model Function Modeling (IDEF0)
4.2.2 DoD Manual 8320.1-M-1, DoD Data
Data Model Standardization Procedures, January 1993
- FIPS 184
Integration Definition for Information
Modeling (IDEF1X)
4.2.3 DoD Manual 8320.1-M-1, DoD Data
DoD Data Standardization Procedures, January 1993
Definitions
- Defense Data Dictionary System (DDDS),
Version 3.2, May 1996
4.2.4.2.1 JTIDS Technical Interface Design Plan -
JSeries Family Test Edition (TIDP-TE), Reissue 3 August
of Message 1994
Standards
- STANAG 5516, Edition 1, Tactical Data
Exchange - LINK 16, Ratified 2 March 1990
- VMF Technical Interface Design Plan - Test
Edition (TIDP-TE), Reissue 1 February 1995
4.2.4.2.2 MIL-STD-6040, United States Message Text
US Message Text Format (USMTF)
Format (USMTF)
Messages
4.2.4.2.3. Database-to-Database Exchange shall use
Database-to- standard data elements from DDDS, Version 3.2,
Database May 1996
Exchange
Human-Computer Interfaces Mandated Standards
JTA SECTION & MANDATED STANDARD, TITLE, & DATE BASE STANDARDS
SERVICE AREA PROFILED
5.2.1 DoD HCI Style Guide, TAFIM Version 2.0,
General Volume 8, 30 September, 1994.
5.2.2.1 Open Software Foundation (OSF)/Motif
Commercial Style Guide, Revision 1.2 (OSF 1992)
Style Guides
- The Windows Interface: An Application
Design Guide, Microsoft Press, 1992
5.2.2.2 DoD HCI Style Guide, TAFIM Version 2.0,
DoD HCI Style Volume 8, 30 September, 1994.
Guide
5.2.2.3 User Interface Specification for the
Domain-level Defense Information Infrastructure
Style Guides (DII), June 1996
Information Systems Security Mandated Standards
JTA SECTION & MANDATED STANDARD, TITLE, & DATE BASE STANDARDS
SERVICE AREA PROFILED
6.2.2.1 DoD 5200.28-STD, The Department of Defense
Application Trusted Computer System Evaluation
Software Entity Criteria, December 1985
Security
Standards
- NCSC-TG-021, Version 1, Trusted Database
Management System Interpretation, April
1991
- FORTEZZA Application Implementors' Guide,
MD40021011.52, 5 March 1996
- FORTEZZA Cryptologic Programmers' Guide,
MD40005011.52, 30 January 1996
6.2.2.2.1 DoD 5200.28-STD, The DoD Trusted Computer
Operating System Evaluation Criteria, December 1985
System Services
Security
6.2.2.2.1.1 ISO/IEC 10164-8, 1993, Information
Security Technology-Open System Interconnection -
Auditing and Systems Management - Part 8: Security Audit
Alarms Trail Function (ITU-T X.740)
Standards
- DoD 5200.28-STD, The DoD Trusted Computer
System Evaluation Criteria, December 1985
- ISO/IEC 10164-7, 1992, Information
Technology-Open System Interconnection -
Systems Management - Part 7: Security Alarm
Reporting Function (ITU-T X.736, 1992)
6.2.2.2.1.2 FIPS PUB 112, Password Usage, NIST, 30 May
Authentication 1985
Security
Standards
- RFC-1510, The Kerberos Network
Authentication Service, V.5, 10 September
1993
6.2.3.1.1 Host FORTEZZA Interface Control Document,
Security Revision P1.5, 22 December 1994
Standards
- FORTEZZA Plus Interface Control Document,
Release 3.0, 1 June 1995
6.2.3.1.1.1 FIBS PUB 180-1, Secure Hash Standard, NIST,
Security April 1995
Algorithms
- FIPS PUB 186, Digital Signature Standard,
NIST, May 1994
- FIPS PUB 185, Escrowed Encryption Standard,
NIST, 9 February 1994
- Key Exchange Algorithm, NSA,
R21-TECH-23-94, 12 July 1994
6.2.3.1.1.2 MIL-STD-2045-48501, Common Security Label
Security
Protocols
- ITU-T Rec. X.509 (ISO/IEC 9594-8.2),
Version 3, The Directory: Authentication
Framework (1993)
- MIL-STD-2045-18500, Message Handling System NSA Documents
Message Security Protocol (MSP) Profile, SDN 701, 702, 703,
October 1993 801, 802
- SDN.903, revision 3.2, Secure Data Network
System (SDNS) Key Management Protocol
(KMP), 1 August 1989
6.2.3.1.1.3 DoD 5200.28-STD, The DoD Trusted Computer
Evaluation System Evaluation Criteria, December 1985
Criteria
Security
Standards
- NCSC-TG-005, Version-1, Trusted Network
Interpretation, July 1987
6.2.3.2.1 FIPS PUB 185, Escrowed Encryption Standard,
Internetworking NIST, 9 February 1994
Security
Standards
- SDN.301, revision 1.5, Secure Data Network
System (SDNS) Security Protocol 3 (SP3),
1989
- MIL-STD-2045-48501, Common Security Label
6.2.5 DoD Human-Computer Interface Style Guide,
Human-Computer TAFIM, Version .2.0, Volume 8, 30 September
Interface (HCI) 1994
Security
Standards
DOCUMENT SOURCES
APPENDIX C - JTA RELATIONSHIP TO DoDDOD STANDARDS REFORM
The DoD Standards Reform was begun in June 1994 when the Secretary of Defense issued his memorandum entitled "Specifications and Standards - A New Way of Doing Business." Secretary Perry directed that performance-based specifications and standards or nationally-recognized private sector standards be used in future acquisitions. He intends by this initiative to eliminate non-value added requirements, and thus to reduce the cost of weapon systems and materiel; remove impediments to getting commercial state-of-the-art technology into our weapon systems; and integrate the commercial and military industrial bases to the greatest extent possible. The Defense Standards Improvement Council (DSIC) directs implementation of the Reform. The DSIC has interpreted and extended the Reform policy through a series of numbered OSD policy memos. These policy memos and other DSIC decisions, newsletters and other standardization related information are posted on the Defense Standardization Program (DSP) Home Page at http://www.acq.osd.mil/es/std/.
The standards and specifications and other standardization documents identified in the Joint Technical Architecture (JTA) can be cited in solicitations without conflicting with the DoD Standards Reform. All JTA documents have been granted Department-wide exemption from the waiver requirement by the Defense Standards Improvement Council. Mandatory application of JTA standardization documents to acquisition solicitations is authorized. Contrary to interpretations that have been made in the recent past by some DoD organizations, the DoD Standards Reform is not eliminating military standards and specifications nor precluding their use. What the Reform is trying to eliminate is the automatic development and imposition of military unique standards and specifications as the cultural norm. The JTA calls out non-Government standards in every case where it makes sense and where it will lead to the use of commercial products and practices that meet the DoD's needs. The JTA only calls out Military and Federal standards and specifications in those instances where no non-Government standard exists that is cost effective and meets the requirement or where the use of the non-Government standard must be clarified to enable interoperability of DoD systems.
Policy Memo 95-1 establishes procedures for waivers for use of specifications and standards cited as requirements in solicitations. These waiver procedures apply to the types of documents that fall under the province of the Defense Standardization Program and are indexed in the DoD Index of Standards and Specifications (DoDISS). Specifically of relevance to the JTA, Policy Memo 95-1 states that non-Government standards, Interface Standards, Federal Information Processing Standards (FIPS), and Performance Specifications do not require waivers. Also, Policy Memo 95-9 provides that international standardization agreements such as NATO STANAGs (and ACPs) do not require waivers. Federal Telecommunications Standards (FED-STDs) do not require a waiver when they qualify as interface standards. All of the above waiver-free document types encompass most of the documents cited in the JTA. The DSP Home Page provides lists of waiver-free documents and in the near future the DoDISS will indicate those documents that can be used without a waiver.
There are a small number of JTA documents that are not among the types of Government documents that are indexed in the DoDISS and are therefore not subject to the Reform waiver policy. Therefore, they also do not require a waiver to be cited in a solicitation. (An example of a JTA document of a type that is not indexed in the DoDISS is DoD 5200.28-STD.) However, the citation of these non-DoDISS documents in solicitations must comply with Service/Agency requirements for preparation and approval of performance-based program unique specifications. A system specification used to procure a C4I system or a weapon system is a program unique specification. Procedures for preparing performance specifications are provided in MIL-STD-961D, Change 1, 22 August 1995 and in the DSP Performance Specification Guide, SD-15, dated 29 June 1995. MIL-STD-961D defines a performance specification as follows: "A specification that states requirements in terms of the required results with criteria for verifying compliance, but without stating the methods for achieving the required results. A performance specification defines the functional requirements for the item, the environment in which it must operate, and interface and interchangeability characteristics." By this definition, documents that define "interface" characteristics can be properly cited in a performance specification. Therefore, JTA non-DoDISS documents that are used to define interface characteristics are not in conflict with service/agency requirements for preparation and approval of performance-based program unique specifications.
Most JTA documents qualify as Interface Standards. Policy Memo 95-6 defines the five types of DoD-prepared standards as: interface standards, standard practices, test method standards, manufacturing process standards, and design criteria standards. Policy Memo 95-1 states that of these types, interface standards and standard practices do not require a waiver when cited in a solicitation. MIL-STD-962C (a standard practice) provides definitions, format, and content direction for military standards. It defines an interface standard as follows: "A standard that specifies the physical, functional, or military operational environment interface characteristics of systems, subsystems, equipment, assemblies, components, items or parts to permit interchangeability, interconnection, interoperability, compatibility, or communications." The use of military and Federal interface standards in solicitations is fully compliant with the DoD Standards Reform.
One of DoD's key acquisition reform goals is to reduce acquisition costs and remove impediments to commercial-military integration by emulating commercial buying practices wherever possible. Thus, for any processes, practices, or methods that are described by a non-Government standard used by Commercial firms and which meet DoD's needs, DoD activities should also be using a non-Government standard instead of applying, developing, or revising a military or Federal Standard. The standards selected for the JTA are predominately non-Government standards. Military or Federal standards have been selected for the JTA only in those instances where non-Government standards failed to satisfy the DoD needs. In most of those instances, in fact, the military or Federal standard is a profile of one or more non-Government standards. The military or Federal profile identifies the chosen classes, subsets, options, and parameters of one or more base standards necessary for achieving interoperability (or other function). In some instances, the profile specifies unique interface requirements not satisfied by the non-Government standard. Therefore the JTA complies fully with this key acquisition reform goal.
USMC SUPPLEMENT
This supplement to the Joint Technical Architecture (JTA) provides standards mandatory for use in the Marine Corps for service areas that do not appear in the JTA.
This sections contains the mandatory standards and standard products for use within the Marine Corps. Where products are specified, their inclusion is the result of one or more competitive procurements scoped to include the entire Marine Corps.
This section adopts the DoD minimum desktop configuration for computers for the Marine Corps and adds certain requirements to support Marine Corps systems and infrastructure. Many new systems being planned for implementation within DoD, such as the Defense Message System (DMS), will provide only part of a whole system. The following minimum configurations satisfies those minimum capabilities which must exist on users' desktops if the users are to effectively meet their DoD missions on the existing and planned USMC infrastructure. The requirements of this section apply to all acquisitions of desktop computers.
The minimum desktop configuration for desktop automation terminals is designed to support user requirements such as connectivity to and operation within the Defense Information Infrastructure (DII), Global Command and Control System (GCCS), and DMS while also supporting local office automation applications. Table USMC-1 shows the desktop configuration for each of these systems and is provided as background. Support for new technology such as multimedia and various interface media such as Personal Computer Memory Card International Association (PCMCIA) slots used to support security in the DMS are included. Table USMC-2 shows the minimum desktop and server configurations for U.S. Marine Corps acquisitions and is mandated for acquisitions.
CG, MCCDC will publish a message each September which will specify the minimum Desktop Computer Configuration which may be purchased for the following Fiscal Year. This guidance will be based on requirements to support current missions as well as assumptions concerning future requirements. In compliance with Executive Order 12845, the above minimum desktop configuration must meet Environmental Protection Agency (EPA) Energy Star requirements.
Table USMC-1 - DoD Desktop System Configurations
DOD DESKTOP SYSTEM
CONFIGURATIONS
DMS GCCS DII
> 33 MHz clock speed > 66 MHz clock speed > 66 MHz clock speed
> 32-bit data path > 32-bit data path > 32-bit data path
> 8K of internal > 8K of internal cache > 8K of internal
cache < 5 volts cache
< 5 volts > 36 integer SPECmark < 5 volts
> 36 integer SPECmark > 16 floating point > 36 integer SPECmark
> 16 floating point SPECmark > 16 floating point
SPECmark SPECmark
16M RAM expandable to 16M RAM expandable to 16M RAM expandable to
32M 32M 32M
At least 500 MB hard At least 1 GB hard At least 1 GB hard
drive drive drive
The computer must The computer must The computer must
support user specific support user specific support user specific
requirements for LAN requirements for LAN requirements for LAN
connectivity. connectivity. connectivity.
2-PCMCIA type II 2-PCMCIA slots 2-PCMCIA slots
slots
SVGA (1024x768 SVGA controller with SVGA controller with
resolution) 1MB RAM 1MB RAM
- CD-ROMCD-ROM Reader CD-ROM Reader
- 3.5" floppy drive 3.5" floppy drive
- 2-parallel and 2-parallel and
2-serial ports 2-serial ports
- 3-button mouse 3-button mouse
- 17" color monitor 17" color monitor
Table USMC-2 - Minimum USMC Desktop and Server System Requirements
Personal Computer Server Configuration
Minimum Configuration
IBM Compatible Certified for intended Network
Operating System
> 66MHz Processor Clock Speed > 100 MHz Processor Clock Speed
8 kbytes of Internal Cache
- Support DX2 Intel Implementation or
Better
32-bit Data Path 100% Compatible EISA/PCI Bus
- Four EISA/PCI 32-bit Expansion
Board Slots
Two EISA/PCI 64-bit Expansion Board
Slots
One EISA/PCI Shared 64-bit
Expansion Board Slots
5 Volt
EPA Energy Star Compliant
36 Integer SPECMark
16 Floating Point SPECMark
16 Megabytes RAM, Expandable to 32 64 Megabytes of RAM, 70 nS Speed,
Megabytes Extended RAM Memory with the
Capability to Increase Total Memory
to 128 Megabytes
1 Gigabyte or 2 - 500 Megabyte Two 1 Gigabyte Hard Drives
Hard Drive
2 PCMCIA Type II Slots or 1 Type
III
- One EISA/PCI Fast SCSI II
Controller Card or Better
SVGA Controller with 1 Megabyte
RAM, 1024x768 Pixels, 256 Colors
LAN Connectivity
- Real-time Clock with Battery Backup
3.5-inch Floppy Drive 3.5-inch Floppy Drive
2 Parallel and 2 Serial Ports
Pointing Device with a Minimum of
2 Buttons
- 1 2/4 Gigabyte 4mm Digital Audio
Tape Unit
- EISA/CMOS Configurable to 512k
- Base RAM to Support 5 ICA Cards
14 inch Color Monitor
Table USMC-3 is a list of the required standard software products by applications category. For individuals performing tasks in one of these application areas, these software packages are those authorized for purchase and use on USMC Personal Computer-Class Systems.
Table USMC-3 - Required Software Products
Software Category Selected Product Standard Issue Programming Language Ada (Developmental) Specialty Items Asynchronous Communications TBD Audit Software TBD Client/Server OS TBD Decision Support TBD Desktop Publishing TBD Disk Management TBD Document Management TBD Internet Web Browser TBD Internet Image Editor TBD Message Release TBD Network Management Local Management TBD Regional Management TBD Project Management TBD SQL Database Oracle Voice Recognition TBD
In addition to the TELNET requirements found in Section 3.2.1.1.1.4, Remote Terminal, the following standards are mandated:
This supplement does not specify any standards in this area.
This supplement does not specify any standards in this area.
This supplement does not specify any standards in this area.
This supplement does not specify any standards in this area.
[End JTA]